How to Crochet Chic Fingerless Gloves with a Woven Stitch Pattern

Materials & tools you'll need

Abbreviations used in this tutorial

Step 1 — Work the foundation chain

Using your chosen yarn and hook, make a foundation chain long enough to wrap comfortably around your hand just below the knuckles — the exact stitch count will vary depending on your yarn weight and hook size. The foundation chain sets the width of the glove body, so take the time to hold it against your hand before proceeding. If you are working in worsted weight yarn with a US H (5mm) hook, a chain of around 30 to 36 stitches is a good starting point for an average adult hand. Use a stitch marker to mark the first stitch of the chain so you can find it easily when you begin the first row of the glove body.

Step 2 — Build the glove body with the woven stitch pattern

Work in rows of fpdc, bpdc, and dc stitches as set out in the pattern to build the woven texture across the glove body. The woven effect is created by alternating front post and back post double crochet stitches — the fpdc pulls the stitch forward toward you while the bpdc pushes it to the back, producing raised vertical columns that mimic a woven fabric. Traditional dc stitches are worked between the post stitches to fill the fabric and maintain an even stitch count. Continue working rows in this pattern until the glove body reaches your desired length — typically enough to cover from the base of the palm to just below the knuckles. Keep your tension even throughout so the woven pattern sits consistently across all rows.

Step 3 — Add the ribbed cuff

Make a foundation chain for the cuff at the wrist end of the glove body, then work rows of alternating fpdc and bpdc stitches to create a ribbed texture. The rib pattern is formed by working fpdc directly above each fpdc from the previous row and bpdc directly above each bpdc — this consistency is what builds the raised rib columns. Continue working the ribbed rows until the cuff reaches your preferred depth; a cuff of around 4 to 6 rows gives a neat wrist band with enough stretch to fit comfortably over the hand when putting the glove on. Fasten off and weave in the cuff ends securely once the cuff is complete.

Step 4 — Create the thumb opening

Mark the position of the thumb opening on the side of the glove body with a stitch marker — this is typically placed about one third of the way up from the wrist end of the glove. Work a short row of chain stitches to bridge across the thumb gap, skipping the equivalent number of stitches on the glove body to create an opening wide enough for the thumb to pass through comfortably. On the following row, work dc stitches back across the chain stitches to close the top of the opening and maintain the stitch count. The thumb opening does not need to be large — just enough to allow the thumb to sit naturally without pulling the glove out of shape.

Step 5 — Work the adjustable strap

Make a foundation chain for the strap using the same yarn and hook as the glove body, then work rows of dc stitches to build the body of the strap to your desired length. The strap wraps around the wrist over the cuff and fastens with a button, allowing the fit to be adjusted for different wrist sizes. At one end of the strap, work a buttonhole by chaining 3 to 4 stitches and skipping the same number of dc stitches — this creates an opening approximately 1 inch (2.5 cm) in diameter that is large enough to pass a standard button through without stretching. Work dc stitches back across the chain on the next row to stabilise the buttonhole edges. Fasten off and weave in all strap ends.

Step 6 — Attach the strap and sew on the button

Position the strap across the wrist section of the glove, centred over the cuff, and pin it in place before sewing. Using the tapestry needle and a length of matching yarn, sew the non-buttonhole end of the strap securely to the glove body at the centre of the second woven-stitch row, working several passes through the strap and glove fabric to ensure a firm attachment. Once the strap is secured, sew the fastening button to the opposite side of the glove at the corresponding position — the button should align naturally with the buttonhole when the strap is wrapped around the wrist. Knot the button yarn firmly on the inside of the glove and weave in the tail so it does not work loose with wear.

Step 7 — Finish and block the gloves

Go back through all sections of both gloves and fasten off any remaining open rows by weaving the yarn tails through the back loops of several neighbouring stitches in at least two directions, then trim close to the fabric. Check all seams and joins from the outside to confirm there are no gaps or loose threads. If desired, block the finished gloves by lightly dampening them and laying them flat on a blocking mat, shaping them gently to even out the woven stitch pattern and encourage the ribbed cuff to sit flat. Follow the blocking recommendations for your specific yarn — most wool and wool-blend yarns benefit from wet blocking, while acrylic yarns respond better to steam or simply being worn in. Allow the gloves to dry completely before wearing or gifting.

Frequently asked questions

What materials do I need to crochet fingerless gloves with a woven stitch pattern?
You will need worsted or bulky weight yarn, a crochet hook appropriate for your yarn (such as a US H / 8mm for worsted weight), stitch markers, and a tapestry needle for weaving in ends and securing stitches. Choose a soft, smooth yarn with good stitch definition for best results.

How do I create a ribbed cuff for fingerless gloves using fpdc and bpdc?
Make a foundation chain at the wrist end of the glove, then work rows alternating front post double crochet (fpdc) and back post double crochet (bpdc) stitches, keeping each post stitch directly above the matching stitch from the previous row. Continue until the cuff reaches your preferred depth, then fasten off and weave in all ends securely.

How do I add an adjustable strap with a buttonhole to fingerless gloves?
Work a foundation chain for the strap and crochet rows of dc to build the strap body. At one end, create a buttonhole by chaining 3 to 4 stitches and skipping the same number of dc stitches, then stabilise the edges on the following row. Sew a button at the corresponding position on the opposite side of the glove and weave in all ends.

Can beginners make fingerless gloves with a woven stitch pattern?
This project is rated intermediate. It is suitable for crocheters comfortable with basic double crochet who are ready to learn front post and back post variations. If you are new to post stitches, practise fpdc and bpdc on a small swatch before starting the gloves.

What safety precautions should I take when crocheting with new yarns or dyes?
Some yarns or dyes may cause skin or respiratory irritation. When working with unfamiliar materials, consider wearing gloves and working in a well-ventilated area. Always check the yarn label for any fibre or dye warnings before starting your project.

Enjoyed this tutorial?

Find 60+ free tutorials on YouTube. Grab a pattern from the Etsy shop, or go deeper with a community membership.

Free tutorials on YouTube →    Shop on Etsy →    Join the community →