How to Crochet a Triangular Headband

Materials & tools you'll need

Step 1 — Create the chain starter

Begin by chaining 4 stitches using your main colour yarn. Join the chain into a loop with a slip stitch — this small loop forms the foundation ring from which the entire headband grows. Keep your tension relaxed and consistent; too tight a starting loop will make the first few rows difficult to work into. This slip stitch join is the anchor point for all subsequent rows, so make sure it sits flat and even before moving on.

Step 2 — Crochet the base

Using your main colour yarn, work double crochet (dc) stitches across the row until you reach your desired base length. The number of stitches you need depends on the head circumference of the wearer — measure around the head with a flexible tape measure and use that figure as your guide. Aim for a firm but not stiff tension; the base row sets the width of the entire triangle, so even stitches here will make the rest of the project much easier to manage.

Step 3 — Form the triangle sides

Turn the work so the wrong side faces you. Chain 1 stitch to turn, then work a double crochet into the first dc from the bottom of the previous row on each side. Repeat this process — turning, chaining 1, and working dc into the first stitch on each side — until three sides of the triangle are formed. This creates a right-angled triangle with two shorter sides rising from the longer base. Keep each row tidy and make sure the edge stitches are worked consistently so the sides of the triangle remain straight.

Step 4 — Increase the height of the triangle

Continue working in double crochet stitches across each row, turning at the end of each row, until the triangle reaches your desired height. Check regularly that the rows are evenly distributed and that the triangle is maintaining its shape — the two shorter sides should be equal in length and angle. If either side begins to lean or pull, adjust your tension slightly before continuing. The finished triangle should lie flat without curling at the edges.

Step 5 — Add the border

Switch to your second colour yarn, joining it at the top corner where all three sides of the triangle meet. Work single crochet (sc) stitches evenly around the entire border of the triangle, joining with a slip stitch as needed at each corner to keep the fabric flat. Take care not to close or join the base of the triangle while working the border — the base must remain open to allow the tie closures to sit correctly. The contrast colour border frames the headband neatly and adds a polished finish to the edges.

Step 6 — Create the ties

To create each tie, chain 50 stitches from the end of the base. Work single crochet stitches along the bottom edge of the chain, then work sc back along the top of the tie to connect and secure both edges. This gives each tie a neat, double-layered structure that holds its shape and sits comfortably against the skin. The length of the ties can be adjusted — chain more or fewer stitches depending on how much length you need to tie a bow or knot comfortably at the back of the head.

Step 7 — Weave in ends

Once all crochet work is complete, use a yarn needle or your hook to carefully weave in any remaining yarn ends. Work each end in at least two directions through the stitches so it cannot pull free with wear. Trim close to the fabric once secure. Pay particular attention to the join where you switched to the border colour — this area often has two or more ends that need to be woven in separately. A clean finish here makes the headband look professional and ensures it holds up well over time.

Step 8 — Finish and wear

Your triangular crochet headband is now complete. Place the wide triangle section at the front of the head and tie the two long ties at the back — adjust the knot or bow to your preferred tightness. The tie closure means the headband fits a range of head sizes without modification, making it an excellent project to give as a gift. Experiment with different yarn colours for the main body and border to create entirely different looks from the same pattern.

Frequently asked questions

What materials do I need to crochet a triangular headband?
You will need two colours of yarn — one for the main body and one for the border — a crochet hook sized to match your yarn (a G/4.5mm hook works well for most yarns), and scissors.

Can I use any yarn for this project?
Yes, but choose a yarn that works well with double crochet and single crochet stitches. Adjust your hook size based on the thickness and texture of your chosen yarn to achieve an even tension.

How long should the base of the triangle be?
The base length depends on the head circumference of the wearer. Measure around the head with a flexible tape measure and use that measurement to determine the number of double crochet stitches needed for the base row.

How do I form the triangle sides?
Turn the work so the wrong side faces you, chain 1 for turning, then work double crochet stitches into the first dc on each side. Repeat on each subsequent row until three sides of the triangle are formed — two shorter sides and one longer base.

Enjoyed this tutorial?

Find 60+ free tutorials on YouTube. Grab a pattern from the Etsy shop, or go deeper with a community membership.

Free tutorials on YouTube →    Shop on Etsy →    Join the community →