How to Crochet a Spring Flower

Materials & tools you'll need

Step 1 — Make the slipknot and foundation ring

Start with a slipknot on your hook, then chain 3. Slip stitch into the first chain you made to join it into a small ring — this gives you the hole you'll be working your first round of stitches into.

Step 2 — Work Round 1, the base circle

Chain 2 (this chain-2 will count as your first half double crochet), then work 9 more half double crochets into the ring, for a total of 10 stitches around. Join the round by slip stitching into the top of your starting chain-2.

Step 3 — Expand the center with Round 2

Chain 1, then work 2 half double crochets into each of the 10 stitches from Round 1, all the way around. This doubles your stitch count to 20 and gives the center of the flower a little more room before the petals begin. Join with a slip stitch into the top of your starting chain.

Step 4 — Create the petal loops

Using your 20 stitches as a guide, chain 4 and slip stitch into the 4th chain from your hook to form a loop. Repeat this chain-4- and-slip-stitch loop 5 times in total, spacing them evenly around the circle — this gives you 5 petal foundations to build on in the next step.

Step 5 — Build up the petals

Chain 1, then work 6 half double crochets into the first chain-4 loop from Step 4. Slip stitch into the same base point where that loop was originally attached, then chain 1 and work 6 more half double crochets into the next loop. Repeat around all 5 petal loops — you'll end up with 30 stitches total. The petals will naturally begin to curl upward here, which is exactly what gives the flower its cupped shape.

Step 6 — Add height and curve to the petals

Chain 1, then work into the same 6 stitches of each petal as follows: 2 single crochets, 2 half double crochets, and 2 single crochets, joining with a slip stitch at the same base point each time before moving to the next petal. Repeat this sequence for all 5 petals. This round doesn't add any new stitches, so the petals will start to curve inward rather than expand — that's normal and gives the flower its finished look. This is also a good point to switch to a different colour of yarn if you'd like a two-tone flower; a variegated yarn works especially well here for a soft, springtime effect.

Step 7 — Finish off and shape the flower

Once you've joined the last petal back to the beginning with a slip stitch, chain 1, then trim your yarn and pull it through tightly to secure. Weave in any loose ends with a tapestry needle, then gently adjust the petals by hand until the flower sits the way you like. Keep in mind that the longer you work a petal, the more it will curve inward, so you can fine-tune the shape as you go.

Frequently asked questions

What materials do I need to crochet a spring flower?
You will need approximately 75 yards of acrylic or cotton yarn, a 3.75mm aluminum crochet hook, a tapestry needle for weaving in ends, stitch markers, and scissors.

What skill level is required to make this crochet spring flower?
This is a beginner-friendly project worked in the round using half double crochet. The finished flower measures approximately 3 inches in diameter.

How can I adjust the size of my crochet spring flower?
You can make the flower bigger or smaller by using a larger or smaller crochet hook, or by using a thicker or thinner yarn. The stitch counts in the pattern will stay the same either way.

Can I layer multiple crochet flowers together?
Yes. Stacking several of these flowers on top of each other, in matching or contrasting colours, creates a fuller look similar to a carnation or rose.

Enjoyed this tutorial?

Find 60+ free tutorials on YouTube. Grab a pattern from the Etsy shop, or go deeper with a community membership.

Free tutorials on YouTube →    Shop on Etsy →    Join the community →